adc-dac-baremetal
Bare-metal ADC and DAC skill. Use when configuring analog sampling, DMA-driven ADC, calibration, or DAC output on MCUs. Activates on queries about ADC bare-metal, sampling time, DMA ADC, or DAC channel setup.
Savant verdict: Analyzed
Scanned or evaluated by Savant; not yet both passing.
Live evaluation
Not evaluated yet. Workspaces can request a live evaluation.
Security assessment
Risk score
0/100
Recommendation
SAFE
Severity
LOW
Savant decision
Passed
The security assessment rated this package safe. Static security analysis completed.
0 patterns found
Structure
- No license declaredConfirm you may reuse this skill before importing it into your repository.
SKILL.md
---
name: adc-dac-baremetal
description: Bare-metal ADC and DAC skill. Use when configuring analog sampling, DMA-driven ADC, calibration, or DAC output on MCUs. Activates on queries about ADC bare-metal, sampling time, DMA ADC, or DAC channel setup.
---
# ADC and DAC (Bare-Metal)
## Purpose
Configure ADC and DAC peripherals: channel selection, sampling times, calibration sequences, DMA circular buffers, and DAC static/dynamic output.
## When to Use
- Reading analog sensors (temperature, voltage)
- Audio or control voltage output via DAC
- Continuous sampling with DMA
- Post-reset ADC calibration on STM32
## Workflow
### 1. STM32 ADC single conversion
```c
/* Enable ADC1 and GPIOA clock; PA0 analog mode */
ADC1->CR2 |= ADC_CR2_ADON;
for (volatile int i = 0; i < 10000; i++); /* stabilization — RM value */
ADC1->SMPR2 |= ADC_SMPR2_SMP0_2; /* 84 cycles sample time ch0 */
ADC1->SQR3 = 0; /* channel 0, 1 conversion */
ADC1->CR2 |= ADC_CR2_SWSTART;
while (!(ADC1->SR & ADC_SR_EOC))
;
uint16_t sample = ADC1->DR;
```
Run `ADC_Calibration()` / `ADC_CR2_RSTCAL/CAL` per RM on F1/F4 families.
### 2. DMA circular ADC
```c
/* ADC1 → DMA2 Stream0, circular mode into buffer[64] */
/* Configure DMA: periph-to-mem, halfword, increment mem, circular */
ADC1->CR2 |= ADC_CR2_DMA | ADC_CR2_CONT;
DMA2_Stream0->CR |= DMA_SxCR_EN;
```
Half-transfer / transfer-complete IRQs for double buffering.
### 3. DAC output (STM32)
```c
RCC->APB1ENR |= RCC_APB1ENR_DACEN;
DAC->CR |= DAC_CR_EN1;
DAC->DHR12R1 = 2048; /* mid-scale 3.3V reference */
```
### 4. Agent usage
```
/adc-dac-baremetal Set up ADC1 channel 0 with DMA circular buffer
```
## Common Problems
| Symptom | Cause | Fix |
|---------|-------|-----|
| Noisy readings | Short sample time | Increase SMP bits |
| Stuck EOC | Clock not enabled | RCC ADC enable |
| Wrong voltage | Vref not 3.3V | Measure VDDA; calibrate |
| DMA corrupt | Buffer alignment | Use `uint16_t` aligned buffer |
## Related Skills
- `skills/baremetal/dma-baremetal` — ADC DMA streams
- `skills/baremetal/timers-pwm-baremetal` — ADC external trigger
- `skills/baremetal/gpio-baremetal` — analog pin mode